FR E520 3.7K PDF

FR-EK to K(C). FR-EK to K(C) ○Removal. (For the FR- EK to K, FR-ESK to K, FR-EW-. K to K). FR-E FR-EKND to KND. INSTRUCTION MANUAL. OUTLINE Economy, Trade and Industry) in September, applies to the K and less. : USED MITSUBISHI FR-EK-NA,FR-PA INVERTER, 5hp, v,BOXYB: Everything Else.

Author: Maulrajas Kajishakar
Country: Czech Republic
Language: English (Spanish)
Genre: Music
Published (Last): 17 October 2010
Pages: 421
PDF File Size: 5.78 Mb
ePub File Size: 5.10 Mb
ISBN: 169-9-41419-270-1
Downloads: 1696
Price: Free* [*Free Regsitration Required]
Uploader: Malazshura

Parameter Factory Setting Range The setting of this function is valid for the combined, PU, external and communication operations. Don’t show me this message again. Page – User group selection Pr. Otherwise, you may access the exposed high-voltage terminals or the 3.7l part of the circuitry and get an electric shock.

Page – Capacitor life alarm Pr. You can make parameter setting to output the minor fault signal.

Safety Perform test operation after making sure that safety is ensured if the machine should become out of control. Terminal SE is common to the open collector output signals. Once your information is submitted, an EU Automation team member will respond as soon as possible.

Mitsubishi Electric FR-E520 Instruction Manual

Output Phase Failure Protection Selection pr. Zero Current E20 pr. Thanks for your message. Page – Stop selection Pr. Measure the input signal level.


Single-phase V power input! Do not fit capacitive equipment such as power factor correction capacitor, radio noise filter or surge suppressor to the output of the inverter. Page of Go. Set “1” in Pr. Just send us your name, company, telephone number and email to receive a price as soon as possible.

As soon as the regenerative energy has reduced, deceleration resumes. Table of Contents Add to my manuals Add. Computer Link Operation pr. Change the setting of built-in frequency setting potentiometer valid Pr.

Page – DC injection brake Pr. The optional brake resistor cannot be used with 0. Thank you for choosing the Mitsubishi Transistorized inverter. Name Company Telephone Email.

Power supply harmonics are different in generation source, frequency band and transmission path from radio frequency RF noise and leakage currents. Page 82 – Combined operation mode 1 Operation usi When the operation panel is used, the same value as on the PU is 3.7j displayed: Always make sure that polarity is correct to prevent damage etc. Parameter Write Disable Selection pr.

Make calibration using Pr.

FR-E520-3.7K.Mitsubishi inverter (used)

A member of our team will respond as soon as possible. OV3 Ff OV During Dec Name Regenerative e502 shut-off during deceleration or stop If regenerative energy causes the inverter’s internal main circuit DC voltage to reach or exceed the specified value, the Description protective circuit is activated to stop the inverter output.


Using the key, MODE Corrective action Reduce the load weight. Offline Auto Tuning Function pr. Set any of the following values in Pr. Fr-esc to sc-ene; fr-essc to sc-ene 38 pages.


This may cause a gravity drop when the inverter is used in vertical lift application. Always read this chapter before using the equipment.

Check that the input signal lines are not affected by external noise. Page Page – Electronic thermal relay function Pr. Page 97 – Base frequency, base frequency voltage Dc Injection Brake pr. Chapter 6 Chapter Do not connect terminals SE Motor need not be connected. The electronic thermal reray function does not guarantee protection of the motor from overheating. Therefore, fix the motor securely with a mechanical brake, or before tuning, make sure that there will be no problem in safety if the motor runs.

The inverter station numbers may be set between H00 and H1F stations 0 and 31 in hexadecimal. Before using the inverter, please read this manual carefully to use the equipment to its optimum.